Stock Number: ATT157
Make: Manitou
Model: 60" Forks
Year: 2008


Stock Number: 208107
Make: CAT
Model: P5000-LE
Year: 2014


Stock Number: EQU007777
Make: Kalmar
Model: KLMV25-1200
Year: 1985


Stock Number: 207498
Make: Hyundai
Model: 20BT-7
Year: 2013


Stock Number: 2-16-261627
Make: Potain
Model: IGO50
Year: 2006


Stock Number: 300306
Make: CAT
Model: GP25N5
Year: 2015


Stock Number: 2-05-207082
Make: Hyundai
Model: 35L-7A
Year: 2013


Stock Number: 206519
Make: Hyundai
Model: 250D-7E
Year: 2012


Stock Number: 300632
Make: JLG
Model: M600JP
Year: 2016


Stock Number: 2-18-UEF98
Make: Misc
Model: FORKS


Stock Number: 206595
Make: Hyundai
Model: 70D-7E
Year: 2012


Stock Number: 232203
Make: WackerNeuson
Model: WK HI400HD D
Year: 2013


 
Doosan Gas Forklifts

Doosan Gas Forklifts

The turning radius on a lift truck is also referred to as the turning circle. This piece of information is important for a machine operator to have. It gives the driver the information of how much space is needed to turn the lift truck around. For instance, a tighter turning radius enables the equipment to function successfully in congested areas and tight places, thus improving the forklift's maneuverability. Drivers who are not aware of this measurement may cause damage to the machinery or to the property.

Make the necessary steering geometry alignment corrections before testing the turning radius. The test should start with an operator trainer helping in the cab where they can assist to control the machine's functions. Another person on the ground uses a spray bottle or a hose to wet the outside and inside of the model's wheels. After that, drive the machinery in a complete circle with the wheels turned to the maximum angle. Repeat the procedure once and if necessary, continue to wet the wheels.

Measure the watermarks left by the tires using a tape measure after your measurement test has been completed. The watermark test begins from the tire mark's midpoint to a similar point across the diameter of the circle. For the outside turning diameter, measure the watermark left by the outside tires from one side of the circle to the circle's opposite side. You can determine the inside turning radius by stretching the tape measure across the circle left by the interior tires. Then, divide these numbers in 2 in order to establish the turning radius. Be certain to note that the turning center is the midpoint of the circle's diameter.

Drop a plumb line from the extreme outside radial extension on the equipment in order to establish the wall-to-wall turning diameter. When this is completed, next locate the point on the pavement directly below. This point to the turning center indicates the clearance radius of the equipment. As a rule, wall-to-wall turning diameter is twice the clearance radius of the equipment.

  • Hyster Outdoor Forklift
    Unisource - For over 90 brands of material handling machinery in addition to more than 4.8 million replacement parts and accessories, ... More
  • Mitsubishi Big Forklifts
    Lift truck operators are normally on the trucks more than 7 out of 8 hours per day in several forklift corporations. Operators will be ... More
  • Potain Construction Cranes
    Potain is a world leader in the industry of construction cranes. This is a specific kind which belongs to Manitowoc. They specify in ... More
  • Nissan Stand Up Forklift
    It is totally different to use a stand-up lift truck compared to a sit-down unit. The way you transport and lift cargo along with your ... More
  • Snorkel Boom Lifts
    Back during the year 1946, Wally Johnson began to create the markets for the scaffold towers and aerial work platforms all by himself. ... More